weight controller, weight controller Service Provider in Aurangabad MH

Features

Flexible weighing indicator

Direct Strain Gauge input 4.5 digit resolution

Variable sensitivity from 0.5 to 200mV/V

Excitation 10V 160mA to drive up to 4 load cells

6 wire input to compensate for zener barrier and cable losses

Simple one pass auto calibration for minimum set-up time on site

Auto tare and peak hold actioned by volt-free contacts

Fully isolated 4-20mA and 0-10V analog outputs

RS232 or RS485 communications for setup, data transfer or label/ticket printing

Programmable in-flight compensation for dynamic weighing operations

AC or DC power supply options

Inputs

Calibration       Automatic digital by use of keypad and 1 (or 2) known weights. Manual calibration can also be selected

Auto Tare       By pressing keys ’;>’; and then ’;R’; display will zero. Auto tare value can also be viewed and manually changed if required. Auto tare value is retained on powerdown.

Sensitivity       Preset via DIL switches between 0.5 to 200mV/V

Excitation       10V DC nominal, 150mA maximum

Compensation       By ± sense wires to compensate for cable, connection volt drops and any variation in 10V supply

Accuracy       90 days ± 0.08% of reading ± 0.05% of FS typical

Drift       0.002%ºC typical @ 2.5mV/V

DC Analogue Outputs

DC Voltage       0 to 5V, 0 to 10V, -10 to +10V, Max Current out 50mA

DC Current       0 to 1mA, 0 to 20mA, 4 to 20mA, Max Current out 50mA

Inputs

Accuracy       typical ± 0.08% of output, ± 0.08%FSD

Resolution       as display resolution, max 15 bits

Calibration       by 15-turn pre sets for gain and offset

Inversion       By keypad value

Isolation       ±130V RMS or DC max to analogue input or to any other port

Ranging       Fully keypad scalable over desired display range

PID       Power level, when selected = 12 bit resolution output

Communication Port CP Operation

All display data can be accessed via the communications port along with relay, PID power and EEPROM status. All user configurable data can be changed including EEPROM enable/disable and relay reset (address code cannot be changed).

Type       Details

RS485/422       For up to 32 instruments on 1 bus, 4 wire

20mA       For up to 25 instruments per interface, 4 wire

Cable Length       1km (depending on baud rate)

Baud Rates       300, 600, 1200, 2400, 4800, 9600 (19200 MANTRABUS only)

Electrical Isolation       ±130V RMS or DC max to analogue input or any other port

Formats       MODBUS RTU, MANTRABUS and printer output

Alarm / Control Outputs

SPCO       1 relay on SP1, 2 relays on SP1& 2

DPCO       1 relay on SP1

Relays       230V at 5A AC resistive

Isolation       ±130V RMS

Keypad Programmable Options       Hysteresis, Latching, Output Inversion, Delay Times, PID values and Time Proportioning.

Power Supplies

220V-230V AC 50-60Hz 10W, 110V-120V AC 50-60Hz 10W, 9-32V DC 10W isolated

Base ADW15

Displays       7 segment LED 4.5 digit 10mm.3 x 3mm LED’;s 2 for relay status, 1 for program and hold indication.

Controls

4 membrane panel keys with tactile feedback. 1 scroll key to view/update parameter. 1 digit select key. 1 digit increment key. 1 reset key. Keypad disable by internal links behind front panel. Hold function by digit select key when in input mode.

Data Retention/Protection

Retention       10 years for set up values, minimum of 100,000 write cycles

Protection of Data Function(s)       Watchdog timer giving repeat auto resets. Impending power detection and hold off. Keypad security and time out.

Physical

Case Material       Grey Noryl, flame retardant

Environmental

Storage temperature       -20 to +70ºC

Operating temperature       -10 to 50ºC

Relative humidity       95% maximum non condensing

CE Environmental Approvals       European EMC Directive 2004/108/EC, Low Voltage Directive 2006/95/EC

Send Your Message

Please Enter Valid Email Id

Error message

Enter code:

Our Service

Service Information

weight controller

Features

Inputs
Calibration		Automatic digital by use of keypad and 1 (or 2) known weights. Manual calibration can also be selected
Auto Tare		By pressing keys ’;>’; and then ’;R’; display will zero. Auto tare value can also be viewed and manually changed if required. Auto tare value is retained on powerdown.
Sensitivity		Preset via DIL switches between 0.5 to 200mV/V
Excitation		10V DC nominal, 150mA maximum
Compensation		By ± sense wires to compensate for cable, connection volt drops and any variation in 10V supply
Accuracy		90 days ± 0.08% of reading ± 0.05% of FS typical
Drift		0.002%ºC typical @ 2.5mV/V
DC Analogue Outputs
DC Voltage		0 to 5V, 0 to 10V, -10 to +10V, Max Current out 50mA
DC Current		0 to 1mA, 0 to 20mA, 4 to 20mA, Max Current out 50mA
Inputs
Accuracy		typical ± 0.08% of output, ± 0.08%FSD
Resolution		as display resolution, max 15 bits
Calibration		by 15-turn pre sets for gain and offset
Inversion		By keypad value
Isolation		±130V RMS or DC max to analogue input or to any other port
Ranging		Fully keypad scalable over desired display range
PID		Power level, when selected = 12 bit resolution output
Communication Port CP Operation
All display data can be accessed via the communications port along with relay, PID power and EEPROM status. All user configurable data can be changed including EEPROM enable/disable and relay reset (address code cannot be changed).
Type		Details
RS485/422		For up to 32 instruments on 1 bus, 4 wire
20mA		For up to 25 instruments per interface, 4 wire
Cable Length		1km (depending on baud rate)
Baud Rates		300, 600, 1200, 2400, 4800, 9600 (19200 MANTRABUS only)
Electrical Isolation		±130V RMS or DC max to analogue input or any other port
Formats		MODBUS RTU, MANTRABUS and printer output
Alarm / Control Outputs
SPCO		1 relay on SP1, 2 relays on SP1& 2
DPCO		1 relay on SP1
Relays		230V at 5A AC resistive
Isolation		±130V RMS
Keypad Programmable Options		Hysteresis, Latching, Output Inversion, Delay Times, PID values and Time Proportioning.
Power Supplies
220V-230V AC 50-60Hz 10W, 110V-120V AC 50-60Hz 10W, 9-32V DC 10W isolated
Base ADW15
Displays		7 segment LED 4.5 digit 10mm.3 x 3mm LED’;s 2 for relay status, 1 for program and hold indication.
Controls
4 membrane panel keys with tactile feedback. 1 scroll key to view/update parameter. 1 digit select key. 1 digit increment key. 1 reset key. Keypad disable by internal links behind front panel. Hold function by digit select key when in input mode.
Data Retention/Protection
Retention		10 years for set up values, minimum of 100,000 write cycles
Protection of Data Function(s)		Watchdog timer giving repeat auto resets. Impending power detection and hold off. Keypad security and time out.
Physical
Case Material		Grey Noryl, flame retardant
Environmental
Storage temperature		-20 to +70ºC
Operating temperature		-10 to 50ºC
Relative humidity		95% maximum non condensing
CE Environmental Approvals		European EMC Directive 2004/108/EC, Low Voltage Directive 2006/95/EC